Downloads

Software & Firmware Archiv

Filtern nach Update Typ
Typ
Release Titel
Aktuellste Version
Passende Produkte
Download
Software
6.9.11
Download nicht verfügbar

Important

  • This software release can be used to make new SW6000 installations or upgrade all previous SW6000 installed versions; however it cannot be used to upgrade systems using CU 6005, CU 6010 or CU 6011 Central Units
  • This version is compatible with SW6000 Software License file v1.7 only
  • No new SW6000 license is needed if upgrading from SW6000 v6.0.xxx or later versions
  • A new SW6000 license is needed if upgrading from SW6000 v5.8.xxx or previous versions

New Features

  • CAA
    • Support for MXCIC C-channel
  • CUA
    • Interpretation control support for MXCIC 
    • Include control of multiple interpreter devices on the same screen
    • Agenda icons updated
  • CDA
    • Support for MXCIC C-Channel

Bug Fixes

  • CUA
    • The application now indicates the correct CDA display in the display screen after users press the 'Prepare meeting' button 
    • Fixed an issue where an exception occurred when the CUA window was resized
  • CDA
    • Meeting variables are now cleared when a vote is cancelled
    • No longer uses a default configuration at meeting start/stop when none is selected
    • Fixed a problem where there was an unstable connection when another CDA is shut down
  • CAA
    • Fixed an error in formatting in 'Total Vote Result' window
    • Users can now cancel report generation if data is not present
    • Voting reports have been corrected for ‘No login’ type meetings
    • Update button is now activated after editing groups in the grid for participant table
    • It’s no longer possible to create reply configurations without a name
    • The Date filter in ‘Default participant seat table’ now works as expected
    • Subject vote report in No login mode no longer shows the wrong results
    • Fixed an issue where an error message appeared when clicking the ‘Replace unit’ or ‘Mic scan’ button in Setup | Conference units window
    • Fixed an issue where the Pre-request to speak list shown for an agenda subject was sometimes empty even though a pre-request existed
    • Fixed an issue where importing participants to the participant table failed
    • Operational buttons are no longer disabled after updating the name sign page.
    • Users are now able to import 1,000 Agenda subjects
  • CUI
    • Fixed an issue where speech time was not sent to CCU when CUI reconnected
  • Database
    • Users are now able to install a database using the ‘Remove All’ button during installation
    • Added a fix for updating the ‘Delegate List History’ 

Notes

  • To operate MXC devices with SW6000 version 6.9, the minimum firmware version is 8.5.1.
Firmware
8.5.1

Release notes cover the following models:

  • MXC615
  • MXC620/620-F
  • MXC630/630-F
  • MXC640
  • MXCIC
  • MXCMIU
  • MXCSIGN
  • DIS-CCU

Important

  • This firmware release can be used to update Microflex Complete (MXC), DCS 6000, or DCS 5900 systems using DIS-CCU, CU 5905, CU 6105, or CU 6110 Central Units.
  • Systems using CU 6000, CU 6005, CU 6010 and CU 6011 Central Units are not supported in this release.
  • Firmware Upgrade Utility (FUU) v1686, which is included in the release, is required to update MXC devices. 

New Features

  • MXCMIU
    • Support for XLR input in the MXCMUI when configured as single unit. The use of this input is configured in the DIS-CCU CGUI. The following audio input options are available in the ‘Devices setup’ screen:
      • Port A
      • XLR – line
      • XLR – mic
    • The following option is available in the ‘Participant’ screen: 
      • Audio level adjustment: +10 to -20 dB
    • Note: The Port A loudspeaker output and controls are still active when the MXCMUI is configured with XLR audio in.

Improvements

  • MXC640
    • Percent indication in voting result screen is now visible when SW6000 is connected 
  • DIS-CCU (6000 Mode)
    • The state of enabling/disabling of NFC cards is restored after disconnection of SW6000
    • Diagnostics: Cable length info has been removed from the diagnostic report 
    • Diagnostics: Cable break info in the diagnostic event log has been updated to report only one of the units connected to the defective cable

Bug Fixes

  • DIS-CCU
    • Diagnostics: Incorrect seat number was reported in the Event log at Cable break 
    • Diagnostics: Event log did not work when SW6000 was connected
    • Diagnostics: Fixed an error in cable length in the diagnostic report
    • CCU was wrongly storing users’ speaking rights after closing the CUI
  • MXC630
    • Secret voting - LEDs turned off after casting first vote
    • Attendance button was not blinking after inserting NFC card during attendance session
    • Voting buttons were not blinking after inserting an NFC card during a voting session
  • MXC640
    • "Total" text was not translated for 5-button voting
  • MXCMIU
    • Left button functionality Exclusive was not working
  • MXCIC
    • The Request icon was cut in the right side
    • Microphone LED was turning off after receiving a “channel occupied” message
    • Two interpreter devices can have same booth and desk number

Known Issues

  • Some units in systems with greater than 150 units may not be shown in the Network Topology report.
  • Some units may reset when cable breaks in a loop on an EX 6010 unit.
  • MXC640
    • Manually entered voting results are not shown if a normal voting session has not been started first
    • The agenda subject name for a manually entered result may be wrong
    • It is not possible to use an MXC640 configured as dual-delegate unit with SW6000 if the use of NFC cards is enabled

Notes

  • MXC and DCS 6000 firmware files are packaged together in the same release file.
  • To operate MXC devices with version 8.5.1 with other Shure networked systems, see the following list of minimum software and firmware versions:
    • SW6000 6.9.11
Firmware
1.7.6

New Features

  • Support for new bands
  • IR Preset Support for P10R+ parameters

Bug Fixes

  • Resolved a bug that caused the BAL ST and BAL MX IR presets to not be applied.
  • Resolved a bug that caused a mix to be replaced rather than added when setting up CueMode
  • Enforcement of Access Control via Wireless Workbench to devices with remote connection has been fixed

Notes

  • User Guide
  • To operate PSM1000 devices version 1.7.6 with other Shure networked systems, see the following list of supported minimum versions:
    • AXT600 2.1.22
    • Axient Digital 1.2.34
    • ULX-D 2.4.9
    • Wireless Workbench 6.13.1
    • Shure Update Utility 2.4.6
    • ShurePlus Channels 1.4.2
Firmware
1.7.6

New Features

  • Support for new bands
  • IR Preset Support for P10R+ parameters

Improvements

  • Improved squelch performance
  • Improved P10R+ scanning algorithm provides more accurate scan data
  • Volume lock was updated to remain persistent after a power cycle. Added a user control to set volume lock on and off
  • Removed pan control from the home screen when operating in stereo mode
  • Volume Limiter is now set to OFF when restored to its factory default settings

Bug Fixes

  • Resolved a bug that caused the BAL ST and BAL MX IR presets to not be applied.
  • Resolved a bug that caused a mix to be replaced rather than added when setting up CueMode
  • Updated the behavior of some live audio parameter changes so they are all applied immediately, with the exception of volume lock
  • Updated POWER SAVE MODE so it clears internal state after a channel or group scan is performed, which resolves a bug that could cause IR sync mismatches
  • Updated Channel Scan and Group Scan so it clears after cancellation, which resolves a bug that could cause the home screen to not update according to its current operating frequency

Notes

  • User Guide
  • To operate PSM1000 devices version 1.7.6 with other Shure networked systems, see the following list of supported minimum versions:
    • AXT600 2.1.22
    • Axient Digital 1.2.34
    • ULX-D 2.4.9
    • Wireless Workbench 6.13.1
    • Shure Update Utility 2.4.6
    • ShurePlus Channels 1.4.2
Firmware
1.2.34

Improvements

  • Bug fixes

Notes

  • User Guide
  • To operate SBC840 version 1.2.34 with other Shure devices and software, see the following list of minimum versions:
    • Shure Update Utility 2.4.6
    • Wireless Workbench 6.13.1
Firmware
1.2.34

Improvements

  • Bug fixes

Notes

  • User Guides: SBC220SBC240
  • To operate SBC220 or SBC240 version 1.2.34 with other Shure devices and software, see the following list of minimum versions:
    • Shure Update Utility 2.4.6
    • Wireless Workbench 6.13.1
Firmware
1.2.34

Improvements

  • Updated the firmware version number for the purpose of keeping all Axient Digital firmware version numbers aligned for brand-new system installations

Notes

  • User Guide
  • To operate AD610 version 1.2.34 devices with other Shure systems and software, see the following list of minimum versions:
    • Axient Digital AD1/2 and ADX1/1M/2 Transmitters 1.2.34
    • Axient Digital AD4D/Q Receivers 1.2.34
    • Axient AXT400 Receiver 2.1.11
    • Axient AXT100/200 2.1.11
    • SBRC Shure Battery Rack Charger 1.1.5
    • Shure Update Utility 2.4.6
    • ShurePlus Channels 1.4.2
    • Wireless Workbench 6.13.1
Firmware
1.2.34

Improvements

  • Support for RF band Z16 (Japan): 1240 MHz – 1260 MHz
  • Support for G56 (Indonesia, limited to 10mW)

 

Notes

  • User Guides: AD1 | AD2 | ADX1 | ADX1M | ADX2 | ADX2FD
  • AD1/2 and ADX1/1M/2 version 1.2.34 is compatible with devices on version 1.2.34 and below, but it is recommended to update all devices used together to the same firmware version.
  • To operate AD1/2 and ADX1/1M/2 version 1.2.34 devices with other Shure systems and software, see the following list of minimum versions:
    • Axient Digital AD1/2 and ADX1/1M/2 Transmitters 1.2.34
    • Axient Digital AD4D/Q Receivers 1.2.34
    • Axient AXT600 Spectrum Manager 2.1.22
    • SBC240/840/840M Chargers 1.2.34
    • SBRC Shure Battery Rack Charger 1.1.5
    • Shure Update Utility 2.4.6
    • ShurePlus Channels 1.4.2
    • Wireless Workbench 6.13.1
Firmware
1.2.34

Improvements

  • Bug fixes

Notes

  • User Guide
  • To operate SBC840M version 1.2.34 with other Shure devices and software, see the following list of minimum versions:
    • Shure Update Utility 2.4.6
    • Wireless Workbench 6.13.1
Firmware
1.2.34

Improvements

  • Support for RF band Z16 (Japan): 1240 MHz – 1260 MHz
  • Support for G56 (Indonesia, limited to 10mW)

Bug Fix

  • Fixed talk switch support for the AES53 output

Notes

  • User Guide
  • Command Strings
  • AD4D version 1.2.34 is compatible with AD4D devices on version 1.2.34 and below, but it is recommended to update all devices used together to the same firmware version.
  • To operate AD4D version 1.2.34 devices with other Shure systems and software, see the following list of minimum versions:
    • Axient Digital AD1/2 and ADX1/1M/2 Transmitters 1.2.34
    • Axient Digital AD4D/Q Receivers 1.2.34
    • Axient AXT600 Spectrum Manager 2.1.22
    • SBRC Shure Battery Rack Charger 1.1.5
    • Shure Update Utility 2.4.6
    • ShurePlus Channels 1.4.2