Downloads
Software- en firmware-archieven
Firmware
8.0.3
24-01-2020
Bekijk alle updates
These release notes cover the following models:
- MXWNCS2/4/8 Networked Charging Stations
- MXWANI4/8 Audio Network Interfaces
- MXWAPT2/4/8 Access Point Transceivers
- MXW1/2/6/8 Wireless Microphones
Related Links
Improvements
- Implementation of additional security features, including expanded password capabilities
- MXW devices now advertise Dante/AES67 capability in the Shure Web Device Discovery Application
- New Device Reboot button added to the MXWANI Web UI.
- Improvements to the microphones’ out-of-range detection capabilities when moved outside the wireless coverage area of the MXWAPT.
Japan-specific improvements:
- J-DECT update: Microflex Wireless now features up to 96 channels in HD mode to meet J-DECT requirements, adding additional channels (dependent on modes and interference) as well as an improved handling of PHS presence.
In areas with no PHS interference, the new maximum channel capacity is:
| Pre 8.0.3 FW Versions | After 8.0.3 FW Update |
| 40 SD channels | 48 SD Channels |
| 80 HD channels | 96 HD Channels |
However, when PHS interference is present, the maximum number of channels changes to:
| Pre 8.0.3 FW Versions | After 8.0.3 FW Update |
| 16 SD channels | 32 SD Channels |
| 32 HD channels | 64 HD Channels |
Important Note: For customers in Japan that have an existing MXW installation, a unique, one-off update procedure must be performed to take advantage of these additional microphone channels. Without this procedure, the other improvements mentioned above will still take effect but without the J-DECT update. This procedure needs to be conducted onsite by Shure personnel — please contact your local Shure representative for details.
Bug Fixes
- APT2 is not discovered by Shure Device Discovery app following a reboot or factory reset using Dante Controller
- Spectrum scan on an MXW-APT no longer responsive after Density-Mode change
- Spectrum scan calculation of available channels in a given RF environment shows wrong results
- Mics lose pairing after Density-Mode change
- MXW8: Carrier mismatch strings not being shown in selected language
Known Issues
- SystemOn 3.0.1 is compatible with MXW 8.0.3, but will incorrectly warn “Check system requirements, your current firmware version may not be confirmed compatible.”
- Multiple Grand Master Clocks in Dante Controller might appear with mix of AES67 enabled on an MXW-APT as well as an Axient-Digital system on the same subnet
- MXWAPT8: MCU/GUI - Older firmware microphones are not shown in Utility tab
Notes
- To operate MXW version 8.0.3 with other Shure networked systems, see the following list of minimum software and firmware versions:
- SCM820 1.3.3
- Shure Web Device Discovery 1.2.5Shure Update Utility 2.4.6
- SystemOn 3.2
Firmware
8.0.3
24-01-2020
Bekijk alle updates
These release notes cover the following models:
- MXWNCS2/4/8 Networked Charging Stations
- MXWANI4/8 Audio Network Interfaces
- MXWAPT2/4/8 Access Point Transceivers
- MXW1/2/6/8 Wireless Microphones
Related Links
Improvements
- Implementation of additional security features, including expanded password capabilities
- MXW devices now advertise Dante/AES67 capability in the Shure Web Device Discovery Application
- New Device Reboot button added to the MXWANI Web UI.
- Improvements to the microphones’ out-of-range detection capabilities when moved outside the wireless coverage area of the MXWAPT.
Japan-specific improvements:
- J-DECT update: Microflex Wireless now features up to 96 channels in HD mode to meet J-DECT requirements, adding additional channels (dependent on modes and interference) as well as an improved handling of PHS presence.
In areas with no PHS interference, the new maximum channel capacity is:
| Pre 8.0.3 FW Versions | After 8.0.3 FW Update |
| 40 SD channels | 48 SD Channels |
| 80 HD channels | 96 HD Channels |
However, when PHS interference is present, the maximum number of channels changes to:
| Pre 8.0.3 FW Versions | After 8.0.3 FW Update |
| 16 SD channels | 32 SD Channels |
| 32 HD channels | 64 HD Channels |
Important Note: For customers in Japan that have an existing MXW installation, a unique, one-off update procedure must be performed to take advantage of these additional microphone channels. Without this procedure, the other improvements mentioned above will still take effect but without the J-DECT update. This procedure needs to be conducted onsite by Shure personnel — please contact your local Shure representative for details.
Bug Fixes
- APT2 is not discovered by Shure Device Discovery app following a reboot or factory reset using Dante Controller
- Spectrum scan on an MXW-APT no longer responsive after Density-Mode change
- Spectrum scan calculation of available channels in a given RF environment shows wrong results
- Mics lose pairing after Density-Mode change
- MXW8: Carrier mismatch strings not being shown in selected language
Known Issues
- SystemOn 3.0.1 is compatible with MXW 8.0.3, but will incorrectly warn “Check system requirements, your current firmware version may not be confirmed compatible.”
- Multiple Grand Master Clocks in Dante Controller might appear with mix of AES67 enabled on an MXW-APT as well as an Axient-Digital system on the same subnet
- MXWAPT8: MCU/GUI - Older firmware microphones are not shown in Utility tab
Notes
- To operate MXW version 8.0.3 with other Shure networked systems, see the following list of minimum software and firmware versions:
- SCM820 1.3.3
- Shure Web Device Discovery 1.2.5Shure Update Utility 2.4.6
- SystemOn 3.2
Firmware
8.0.3
24-01-2020
Bekijk alle updates
These release notes cover the following models:
- MXWNCS2/4/8 Networked Charging Stations
- MXWANI4/8 Audio Network Interfaces
- MXWAPT2/4/8 Access Point Transceivers
- MXW1/2/6/8 Wireless Microphones
Related Links
Improvements
- Implementation of additional security features, including expanded password capabilities
- MXW devices now advertise Dante/AES67 capability in the Shure Web Device Discovery Application
- New Device Reboot button added to the MXWANI Web UI.
- Improvements to the microphones’ out-of-range detection capabilities when moved outside the wireless coverage area of the MXWAPT.
Japan-specific improvements:
- J-DECT update: Microflex Wireless now features up to 96 channels in HD mode to meet J-DECT requirements, adding additional channels (dependent on modes and interference) as well as an improved handling of PHS presence.
In areas with no PHS interference, the new maximum channel capacity is:
| Pre 8.0.3 FW Versions | After 8.0.3 FW Update |
| 40 SD channels | 48 SD Channels |
| 80 HD channels | 96 HD Channels |
However, when PHS interference is present, the maximum number of channels changes to:
| Pre 8.0.3 FW Versions | After 8.0.3 FW Update |
| 16 SD channels | 32 SD Channels |
| 32 HD channels | 64 HD Channels |
Important Note: For customers in Japan that have an existing MXW installation, a unique, one-off update procedure must be performed to take advantage of these additional microphone channels. Without this procedure, the other improvements mentioned above will still take effect but without the J-DECT update. This procedure needs to be conducted onsite by Shure personnel — please contact your local Shure representative for details.
Bug Fixes
- APT2 is not discovered by Shure Device Discovery app following a reboot or factory reset using Dante Controller
- Spectrum scan on an MXW-APT no longer responsive after Density-Mode change
- Spectrum scan calculation of available channels in a given RF environment shows wrong results
- Mics lose pairing after Density-Mode change
- MXW8: Carrier mismatch strings not being shown in selected language
Known Issues
- SystemOn 3.0.1 is compatible with MXW 8.0.3, but will incorrectly warn “Check system requirements, your current firmware version may not be confirmed compatible.”
- Multiple Grand Master Clocks in Dante Controller might appear with mix of AES67 enabled on an MXW-APT as well as an Axient-Digital system on the same subnet
- MXWAPT8: MCU/GUI - Older firmware microphones are not shown in Utility tab
Notes
- To operate MXW version 8.0.3 with other Shure networked systems, see the following list of minimum software and firmware versions:
- SCM820 1.3.3
- Shure Web Device Discovery 1.2.5Shure Update Utility 2.4.6
- SystemOn 3.2
Firmware
8.0.3
24-01-2020
Bekijk alle updates
These release notes cover the following models:
- MXWNCS2/4/8 Networked Charging Stations
- MXWANI4/8 Audio Network Interfaces
- MXWAPT2/4/8 Access Point Transceivers
- MXW1/2/6/8 Wireless Microphones
Related Links
Improvements
- Implementation of additional security features, including expanded password capabilities
- MXW devices now advertise Dante/AES67 capability in the Shure Web Device Discovery Application
- New Device Reboot button added to the MXWANI Web UI.
- Improvements to the microphones’ out-of-range detection capabilities when moved outside the wireless coverage area of the MXWAPT.
Japan-specific improvements:
- J-DECT update: Microflex Wireless now features up to 96 channels in HD mode to meet J-DECT requirements, adding additional channels (dependent on modes and interference) as well as an improved handling of PHS presence.
In areas with no PHS interference, the new maximum channel capacity is:
| Pre 8.0.3 FW Versions | After 8.0.3 FW Update |
| 40 SD channels | 48 SD Channels |
| 80 HD channels | 96 HD Channels |
However, when PHS interference is present, the maximum number of channels changes to:
| Pre 8.0.3 FW Versions | After 8.0.3 FW Update |
| 16 SD channels | 32 SD Channels |
| 32 HD channels | 64 HD Channels |
Important Note: For customers in Japan that have an existing MXW installation, a unique, one-off update procedure must be performed to take advantage of these additional microphone channels. Without this procedure, the other improvements mentioned above will still take effect but without the J-DECT update. This procedure needs to be conducted onsite by Shure personnel — please contact your local Shure representative for details.
Bug Fixes
- APT2 is not discovered by Shure Device Discovery app following a reboot or factory reset using Dante Controller
- Spectrum scan on an MXW-APT no longer responsive after Density-Mode change
- Spectrum scan calculation of available channels in a given RF environment shows wrong results
- Mics lose pairing after Density-Mode change
- MXW8: Carrier mismatch strings not being shown in selected language
Known Issues
- SystemOn 3.0.1 is compatible with MXW 8.0.3, but will incorrectly warn “Check system requirements, your current firmware version may not be confirmed compatible.”
- Multiple Grand Master Clocks in Dante Controller might appear with mix of AES67 enabled on an MXW-APT as well as an Axient-Digital system on the same subnet
- MXWAPT8: MCU/GUI - Older firmware microphones are not shown in Utility tab
Notes
- To operate MXW version 8.0.3 with other Shure networked systems, see the following list of minimum software and firmware versions:
- SCM820 1.3.3
- Shure Web Device Discovery 1.2.5Shure Update Utility 2.4.6
- SystemOn 3.2
Firmware
8.0.3
24-01-2020
Bekijk alle updates
These release notes cover the following models:
- MXWNCS2/4/8 Networked Charging Stations
- MXWANI4/8 Audio Network Interfaces
- MXWAPT2/4/8 Access Point Transceivers
- MXW1/2/6/8 Wireless Microphones
Related Links
Improvements
- Implementation of additional security features, including expanded password capabilities
- MXW devices now advertise Dante/AES67 capability in the Shure Web Device Discovery Application
- New Device Reboot button added to the MXWANI Web UI.
- Improvements to the microphones’ out-of-range detection capabilities when moved outside the wireless coverage area of the MXWAPT.
Japan-specific improvements:
- J-DECT update: Microflex Wireless now features up to 96 channels in HD mode to meet J-DECT requirements, adding additional channels (dependent on modes and interference) as well as an improved handling of PHS presence.
In areas with no PHS interference, the new maximum channel capacity is:
| Pre 8.0.3 FW Versions | After 8.0.3 FW Update |
| 40 SD channels | 48 SD Channels |
| 80 HD channels | 96 HD Channels |
However, when PHS interference is present, the maximum number of channels changes to:
| Pre 8.0.3 FW Versions | After 8.0.3 FW Update |
| 16 SD channels | 32 SD Channels |
| 32 HD channels | 64 HD Channels |
Important Note: For customers in Japan that have an existing MXW installation, a unique, one-off update procedure must be performed to take advantage of these additional microphone channels. Without this procedure, the other improvements mentioned above will still take effect but without the J-DECT update. This procedure needs to be conducted onsite by Shure personnel — please contact your local Shure representative for details.
Bug Fixes
- APT2 is not discovered by Shure Device Discovery app following a reboot or factory reset using Dante Controller
- Spectrum scan on an MXW-APT no longer responsive after Density-Mode change
- Spectrum scan calculation of available channels in a given RF environment shows wrong results
- Mics lose pairing after Density-Mode change
- MXW8: Carrier mismatch strings not being shown in selected language
Known Issues
- SystemOn 3.0.1 is compatible with MXW 8.0.3, but will incorrectly warn “Check system requirements, your current firmware version may not be confirmed compatible.”
- Multiple Grand Master Clocks in Dante Controller might appear with mix of AES67 enabled on an MXW-APT as well as an Axient-Digital system on the same subnet
- MXWAPT8: MCU/GUI - Older firmware microphones are not shown in Utility tab
Notes
- To operate MXW version 8.0.3 with other Shure networked systems, see the following list of minimum software and firmware versions:
- SCM820 1.3.3
- Shure Web Device Discovery 1.2.5Shure Update Utility 2.4.6
- SystemOn 3.2
App
2.9.1
23-01-2020
Bekijk alle updates
IMPROVEMENTS
Bug fixes
NOTES
- User Guide
- MV88+ User Guide
- Compatible with Android 6.0 and higher.
- NOTE FOR MV88+ USERS: Learn about compatibility with your Android device at www.shure.com/MOTIVcompatibility.
Software
6.9.11
17-01-2020
Bekijk alle updates
Important
- This software release can be used to make new SW6000 installations or upgrade all previous SW6000 installed versions; however it cannot be used to upgrade systems using CU 6005, CU 6010 or CU 6011 Central Units
- This version is compatible with SW6000 Software License file v1.7 only
- No new SW6000 license is needed if upgrading from SW6000 v6.0.xxx or later versions
- A new SW6000 license is needed if upgrading from SW6000 v5.8.xxx or previous versions
New Features
- CAA
- Support for MXCIC C-channel
- CUA
- Interpretation control support for MXCIC
- Include control of multiple interpreter devices on the same screen
- Agenda icons updated
- CDA
- Support for MXCIC C-Channel
Bug Fixes
- CUA
- The application now indicates the correct CDA display in the display screen after users press the 'Prepare meeting' button
- Fixed an issue where an exception occurred when the CUA window was resized
- CDA
- Meeting variables are now cleared when a vote is cancelled
- No longer uses a default configuration at meeting start/stop when none is selected
- Fixed a problem where there was an unstable connection when another CDA is shut down
- CAA
- Fixed an error in formatting in 'Total Vote Result' window
- Users can now cancel report generation if data is not present
- Voting reports have been corrected for ‘No login’ type meetings
- Update button is now activated after editing groups in the grid for participant table
- It’s no longer possible to create reply configurations without a name
- The Date filter in ‘Default participant seat table’ now works as expected
- Subject vote report in No login mode no longer shows the wrong results
- Fixed an issue where an error message appeared when clicking the ‘Replace unit’ or ‘Mic scan’ button in Setup | Conference units window
- Fixed an issue where the Pre-request to speak list shown for an agenda subject was sometimes empty even though a pre-request existed
- Fixed an issue where importing participants to the participant table failed
- Operational buttons are no longer disabled after updating the name sign page.
- Users are now able to import 1,000 Agenda subjects
- CUI
- Fixed an issue where speech time was not sent to CCU when CUI reconnected
- Database
- Users are now able to install a database using the ‘Remove All’ button during installation
- Added a fix for updating the ‘Delegate List History’
Notes
- To operate MXC devices with SW6000 version 6.9, the minimum firmware version is 8.5.1.
Software
8.5.1
17-01-2020
Bekijk alle updates
Release notes cover the following models:
- MXC615
- MXC620/620-F
- MXC630/630-F
- MXC640
- MXCIC
- MXCMIU
- MXCSIGN
- DIS-CCU
Important
- This firmware release can be used to update Microflex Complete (MXC), DCS 6000, or DCS 5900 systems using DIS-CCU, CU 5905, CU 6105, or CU 6110 Central Units.
- Systems using CU 6000, CU 6005, CU 6010 and CU 6011 Central Units are not supported in this release.
- Firmware Upgrade Utility (FUU) v1686, which is included in the release, is required to update MXC devices.
New Features
- MXCMIU
- Support for XLR input in the MXCMUI when configured as single unit. The use of this input is configured in the DIS-CCU CGUI. The following audio input options are available in the ‘Devices setup’ screen:
- Port A
- XLR – line
- XLR – mic
- The following option is available in the ‘Participant’ screen:
- Audio level adjustment: +10 to -20 dB
- Note: The Port A loudspeaker output and controls are still active when the MXCMUI is configured with XLR audio in.
- Support for XLR input in the MXCMUI when configured as single unit. The use of this input is configured in the DIS-CCU CGUI. The following audio input options are available in the ‘Devices setup’ screen:
Improvements
- MXC640
- Percent indication in voting result screen is now visible when SW6000 is connected
- DIS-CCU (6000 Mode)
- The state of enabling/disabling of NFC cards is restored after disconnection of SW6000
- Diagnostics: Cable length info has been removed from the diagnostic report
- Diagnostics: Cable break info in the diagnostic event log has been updated to report only one of the units connected to the defective cable
Bug Fixes
- DIS-CCU
- Diagnostics: Incorrect seat number was reported in the Event log at Cable break
- Diagnostics: Event log did not work when SW6000 was connected
- Diagnostics: Fixed an error in cable length in the diagnostic report
- CCU was wrongly storing users’ speaking rights after closing the CUI
- MXC630
- Secret voting - LEDs turned off after casting first vote
- Attendance button was not blinking after inserting NFC card during attendance session
- Voting buttons were not blinking after inserting an NFC card during a voting session
- MXC640
- "Total" text was not translated for 5-button voting
- MXCMIU
- Left button functionality Exclusive was not working
- MXCIC
- The Request icon was cut in the right side
- Microphone LED was turning off after receiving a “channel occupied” message
- Two interpreter devices can have same booth and desk number
Known Issues
- Some units in systems with greater than 150 units may not be shown in the Network Topology report.
- Some units may reset when cable breaks in a loop on an EX 6010 unit.
- MXC640
- Manually entered voting results are not shown if a normal voting session has not been started first
- The agenda subject name for a manually entered result may be wrong
- It is not possible to use an MXC640 configured as dual-delegate unit with SW6000 if the use of NFC cards is enabled
Notes
- MXC and DCS 6000 firmware files are packaged together in the same release file.
- To operate MXC devices with version 8.5.1 with other Shure networked systems, see the following list of minimum software and firmware versions:
- SW6000 6.9.11
Firmware
1.7.6
3-01-2020
Bekijk alle updates
New Features
- Support for new bands
- IR Preset Support for P10R+ parameters
Bug Fixes
- Resolved a bug that caused the BAL ST and BAL MX IR presets to not be applied.
- Resolved a bug that caused a mix to be replaced rather than added when setting up CueMode
- Enforcement of Access Control via Wireless Workbench to devices with remote connection has been fixed
Notes
- User Guide
- To operate PSM1000 devices version 1.7.6 with other Shure networked systems, see the following list of supported minimum versions:
- AXT600 2.1.22
- Axient Digital 1.2.34
- ULX-D 2.4.9
- Wireless Workbench 6.13.1
- Shure Update Utility 2.4.6
- ShurePlus Channels 1.4.2
Firmware
1.7.6
3-01-2020
Bekijk alle updates
New Features
- Support for new bands
- IR Preset Support for P10R+ parameters
Improvements
- Improved squelch performance
- Improved P10R+ scanning algorithm provides more accurate scan data
- Volume lock was updated to remain persistent after a power cycle. Added a user control to set volume lock on and off
- Removed pan control from the home screen when operating in stereo mode
- Volume Limiter is now set to OFF when restored to its factory default settings
Bug Fixes
- Resolved a bug that caused the BAL ST and BAL MX IR presets to not be applied.
- Resolved a bug that caused a mix to be replaced rather than added when setting up CueMode
- Updated the behavior of some live audio parameter changes so they are all applied immediately, with the exception of volume lock
- Updated POWER SAVE MODE so it clears internal state after a channel or group scan is performed, which resolves a bug that could cause IR sync mismatches
- Updated Channel Scan and Group Scan so it clears after cancellation, which resolves a bug that could cause the home screen to not update according to its current operating frequency
Notes
- User Guide
- To operate PSM1000 devices version 1.7.6 with other Shure networked systems, see the following list of supported minimum versions:
- AXT600 2.1.22
- Axient Digital 1.2.34
- ULX-D 2.4.9
- Wireless Workbench 6.13.1
- Shure Update Utility 2.4.6
- ShurePlus Channels 1.4.2
Page 81 of 146