डाउनलोड

सॉफ्टवेयर और फर्मवेयर अभिलेखागार

अद्यतन प्रकार द्वारा फ़िल्टर करें

प्रकार

रिलीज शीर्षक

नवीनतम संस्करण

एसोसिएटेड उत्पाद

डाउनलोड

फर्मवेयर
6.0.38

Improvements

  • Enhancements to support Designer 6.0.0
  • Additional hardware support

Known Issues

  • The optional ARRAY_HEIGHT_OVERRIDE value sent via command strings must be resent upon power cycle
  • If the ARRAY_HEIGHT_OVERRIDE command is used to set a height that is outside the valid range (122-914 cm), the command will not display an error but internally, the value will be rejected from being set
  • Acoustic reflections from tables can sometimes be mistaken by the MXA920 as another source/talker location.  The symptom is a second talker location coordinate set in front of and higher than the actual talker.  
    • Workaround: Place Coverage Areas to minimize pick-up of table surface reflections
  • Channel Names are not set in the initial attempt of ‘push-to-Dante’. Dante interface resets when Device Name is set.
    • Workaround: Channel Names are set on the 2nd attempt
  • MXA920 LED does not stay on after a reboot if the light settings are set to Unmute = Blue, Mute = Red. Other light combinations work as expected after reboot.
  • When a muted dynamic coverage area is moved when a dedicated coverage area has also been established, the mix output of the MXA920 has low-level audio from outside the dedicated coverage area limits.  
    • Workaround: Unmute and Mute the dynamic coverage area after a dynamic coverage area is moved

Notes

  • User Guide
  • Command Strings
  • Note that Talker Position Events are published for talkers in a coverage area regardless of the mute status of the coverage area.  To fully inform camera switching decision logic, subscribe to the Coverage Area Mute Status. See https://pubs.shure.com/command-strings for further information
  • To operate this version of MXA920 with Dante Controller, reference the following minimum versions:
    • v3.10.2.4 (Windows)
    • v3.10.2.3 (Mac OS X)
  • To operate this version of MXA920 with Shure software or other Shure networked systems, reference the following list of recommended versions supported:
    • Designer 6.0.0
    • IntelliMix Room 4.2.0
    • ANI22/ANI4IN/ANI4OUT 6.0.41
    • ANIUSB 6.0.44
    • MXA310 6.0.23
    • MXA710 6.0.24
    • MXA910 6.0.24
    • MXA901 6.0.39
    • MXA902 6.0.32
    • MXN5-C 6.0.17
    • MXA-MUTE 6.0.25
    • P300 6.0.38
    • Shure Update Utility 2.8.4
    • Shure Web Device Discovery 1.2.17
फर्मवेयर
6.0.24

Improvements

  • Enhancements to support Designer 6.0.0
  • Additional hardware support

Known Issues

  • When exporting Presets using Safari on a Mac OS, the file type is saved incorrectly and must be renamed to .json to be imported

Notes

  • User Guide
  • Command Strings
  • To operate this version of MXA910 with Dante Controller, reference the following minimum versions:
    • v3.10.2.4 (Windows)
    • v3.10.2.3 (Mac OS X)
  • To operate this version of MXA910 with Shure software or other Shure networked systems, reference the following list of recommended versions supported:
    • Designer 6.0.0
    • ANI22/ANI4IN/ANI4OUT 6.0.41
    • ANIUSB 6.0.44
    • MXA310 6.0.23
    • MXA710 6.0.24
    • MXA920 6.0.38
    • MXA901 6.0.39
    • MXA902 6.0.32
    • MXN5-C 6.0.17
    • MXA-MUTE 6.0.25
    • MXW 10.0.X
    • P300 6.0.38
    • ULXD4D/4Q 2.8.7
    • SCM820 1.4.3
    • Shure Update Utility 2.8.4
    • Shure Web Device Discovery 1.2.17
फर्मवेयर
6.0.24

Improvements

  • Enhancements to support Designer 6.0.0
  • Additional hardware support

Notes

  • User Guide
  • Command Strings
  • To operate this version of MXA710 with Dante Controller, reference the following minimum versions:
    • v3.10.2.4 (Windows)
    • v3.10.2.3 (Mac OS X)
  • To operate this version of MXA710 with Shure software or other Shure networked systems, reference the following list of recommended versions supported:
    • Designer 6.0.0
    • ANI22/ANI4IN/ANI4OUT 6.0.41
    • ANIUSB 6.0.44
    • MXA310 6.0.23
    • MXA910 6.0.24
    • MXA920 6.0.38
    • MXA901 6.0.39
    • MXA902 6.0.32
    • MXN5-C 6.0.17
    • MXA-MUTE 6.0.25
    • MXW 10.0.X
    • P300 6.0.38
    • ULXD4D/4Q 2.8.7
    • SCM820 1.4.3
    • Shure Update Utility 2.8.4
    • Shure Web Device Discovery 1.2.17
फर्मवेयर
6.0.24

Improvements

  • Enhancements to support Designer 6.0.0
  • Additional hardware support

Notes

  • User Guide
  • Command Strings
  • To operate this version of MXA710 with Dante Controller, reference the following minimum versions:
    • v3.10.2.4 (Windows)
    • v3.10.2.3 (Mac OS X)
  • To operate this version of MXA710 with Shure software or other Shure networked systems, reference the following list of recommended versions supported:
    • Designer 6.0.0
    • ANI22/ANI4IN/ANI4OUT 6.0.41
    • ANIUSB 6.0.44
    • MXA310 6.0.23
    • MXA910 6.0.24
    • MXA920 6.0.38
    • MXA901 6.0.39
    • MXA902 6.0.32
    • MXN5-C 6.0.17
    • MXA-MUTE 6.0.25
    • MXW 10.0.X
    • P300 6.0.38
    • ULXD4D/4Q 2.8.7
    • SCM820 1.4.3
    • Shure Update Utility 2.8.4
    • Shure Web Device Discovery 1.2.17
फर्मवेयर
6.0.23

Improvements

  • Enhancements to support Designer 6.0.0
  • Additional hardware support

Known Issues

  • An 802.1X re-authorization request interrupts a firmware update and causes it to fail
    • Workaround: restarting the update will resolve the problem
  • AES67 support is only available on UltimoX hardware
    • MXA310 devices manufactured as of July 2017 are compatible with AES67
  • In AES67 mode - Audio does not pass after changing Dante Device name, followed by a reboot
  • When exporting Presets using Safari on a Mac OS, the file type is saved incorrectly and must be renamed to .json to be imported
  • The Mute Control Function command string response is incorrect when using <GET 0 ALL>
    • When using < GET MUTE_CONTROL_FUNC >, the response is as documented.
    • When using < GET 0 ALL >, the response should be mapped as follows:
< GET 0 ALL > ResponseActual MUTE_CONTROL_FUNC
< REP MUTE_BUTTON ON > ... < REP MUTE_CONTROL_FUNC LOGIC >LOCAL
< REP MUTE_BUTTON ON > ... < REP MUTE_CONTROL_FUNC LOCAL >LOGIC
< REP MUTE_BUTTON OFF >DISABLED

 

Notes

  • User Guide
  • Command Strings
  • To operate this version of MXA310 with Dante Controller, reference the following minimum versions:
    • v3.10.2.4 (Windows)
    • v3.10.2.3 (Mac OS X)
  • Updating all devices used together to the same firmware version is recommended.
  • To operate this version of MXA310 with Shure software or other Shure networked systems, reference the following list of recommended versions supported:
    • Designer 6.0.0
    • ANI22/ANI4IN/ANI4OUT 6.0.41
    • ANIUSB 6.0.44
    • MXA710 6.0.24
    • MXA910 6.0.24
    • MXA920 6.0.38
    • MXA901 6.0.39
    • MXA902 6.0.32
    • MXN5-C 6.0.17
    • MXA-MUTE 6.0.25
    • MXW 10.0.X
    • P300 6.0.38
    • SCM820 1.4.3
    • Shure Update Utility 2.8.4
    • Shure Web Device Discovery 1.2.17
फर्मवेयर
6.0.23

Improvements

  • Enhancements to support Designer 6.0.0
  • Additional hardware support

Known Issues

  • An 802.1X re-authorization request interrupts a firmware update and causes it to fail
    • Workaround: restarting the update will resolve the problem
  • AES67 support is only available on UltimoX hardware
    • MXA310 devices manufactured as of July 2017 are compatible with AES67
  • In AES67 mode - Audio does not pass after changing Dante Device name, followed by a reboot
  • When exporting Presets using Safari on a Mac OS, the file type is saved incorrectly and must be renamed to .json to be imported
  • The Mute Control Function command string response is incorrect when using <GET 0 ALL>
    • When using < GET MUTE_CONTROL_FUNC >, the response is as documented.
    • When using < GET 0 ALL >, the response should be mapped as follows:
< GET 0 ALL > ResponseActual MUTE_CONTROL_FUNC
< REP MUTE_BUTTON ON > ... < REP MUTE_CONTROL_FUNC LOGIC >LOCAL
< REP MUTE_BUTTON ON > ... < REP MUTE_CONTROL_FUNC LOCAL >LOGIC
< REP MUTE_BUTTON OFF >DISABLED

 

Notes

  • User Guide
  • Command Strings
  • To operate this version of MXA310 with Dante Controller, reference the following minimum versions:
    • v3.10.2.4 (Windows)
    • v3.10.2.3 (Mac OS X)
  • Updating all devices used together to the same firmware version is recommended.
  • To operate this version of MXA310 with Shure software or other Shure networked systems, reference the following list of recommended versions supported:
    • Designer 6.0.0
    • ANI22/ANI4IN/ANI4OUT 6.0.41
    • ANIUSB 6.0.44
    • MXA710 6.0.24
    • MXA910 6.0.24
    • MXA920 6.0.38
    • MXA901 6.0.39
    • MXA902 6.0.32
    • MXN5-C 6.0.17
    • MXA-MUTE 6.0.25
    • MXW 10.0.X
    • P300 6.0.38
    • SCM820 1.4.3
    • Shure Update Utility 2.8.4
    • Shure Web Device Discovery 1.2.17
फर्मवेयर
6.0.44

Improvements

  • Enhancements to support Designer 6.0.0
  • Additional hardware support

Known Issues

  • An 802.1X re-authorization request interrupts a firmware update and causes it to fail
    • Workaround: restarting the update will resolve the problem
  • Pop noise is triggered when the channel is unrouted in Dante controller with encryption enabled
  • When exporting Presets using Safari on a Mac OS, the file type is saved incorrectly and must be renamed to .json to be imported.
  • In AES67 mode - Audio does not pass after changing Dante Device name, followed by a reboot

Notes

  • User Guide
  • Command Strings
  • To operate this version of ANIUSB-MATRIX with Dante Controller, reference the following minimum versions
    • v3.10.2.4 (Windows)
    • v3.10.2.3 (macOS)
  • To operate this version of ANIUSB-MATRIX with Microsoft Teams, reference the following minimum versions: 
    • Microsoft Teams Desktop: 1.3.00.24755 
    • Microsoft Teams Rooms: 4.6.20.0
  • To operate this version of ANIUSB-MATRIX with Shure software or other Shure networked systems, reference the following list of recommended versions supported:
    • Designer 6.0.0
    • ANI22/ANI4IN/ANI4OUT 6.0.41
    • MXA310 6.0.23
    • MXA910 6.0.24
    • MXA920 6.0.38
    • MXA901 6.0.39
    • MXA902 6.0.32
    • MXW 10.0.X
    • P300 6.0.38
    • ULXD4D/4Q 2.8.7
    • SCM820 1.4.3
    • Shure Update Utility 2.8.4
    • Shure Web Device Discovery 1.2.17
फर्मवेयर
6.0.41

Improvements

  • Enhancements to support Designer 6.0.0
  • Additional hardware support

Known Issues

  • AES67 support is only available on UltimoX hardware
    • ANI4OUT devices manufactured as of January 2018 are compatible with AES67
  • In AES67 mode - Audio does not pass after changing Dante Device name, followed by a reboot
  • When exporting Presets using Safari on a Mac OS, the file type is saved incorrectly and must be renamed to .json to be imported

Notes

  • User Guide
  • Command Strings
  • To operate this version of ANI4OUT with Dante Controller, reference the following minimum versions:
    • v3.10.2.4 (Windows)
    • v3.10.2.3 (Mac OS X)
  • Updating all devices used together to the same firmware version is recommended.
  • To operate this version of ANI4OUT with other Shure networked systems, reference the following list of recommended versions supported:
    • ANI22/ANI4IN/ANI4OUT 6.0.41
    • ANIUSB 6.0.44
    • MXA310 6.0.23
    • MXA910 6.0.24
    • MXA920 6.0.38
    • MXA901 6.0.39
    • MXA902 6.0.32
    • MXW 10.0.X
    • P300 6.0.38
    • ULXD4D/4Q 2.8.7
    • SCM820 1.4.3
    • Shure Update Utility 2.8.4
    • Shure Web Device Discovery 1.2.17
फर्मवेयर
6.0.41

Improvements

  • Enhancements to support Designer 6.0.0
  • Additional hardware support

Known Issues

  • AES67 support is only available on UltimoX hardware
    • ANI4OUT devices manufactured as of January 2018 are compatible with AES67
  • In AES67 mode - Audio does not pass after changing Dante Device name, followed by a reboot
  • When exporting Presets using Safari on a Mac OS, the file type is saved incorrectly and must be renamed to .json to be imported

Notes

  • User Guide
  • Command Strings
  • To operate this version of ANI4OUT with Dante Controller, reference the following minimum versions:
    • v3.10.2.4 (Windows)
    • v3.10.2.3 (Mac OS X)
  • Updating all devices used together to the same firmware version is recommended.
  • To operate this version of ANI4OUT with other Shure networked systems, reference the following list of recommended versions supported:
    • ANI22/ANI4IN/ANI4OUT 6.0.41
    • ANIUSB 6.0.44
    • MXA310 6.0.23
    • MXA910 6.0.24
    • MXA920 6.0.38
    • MXA901 6.0.39
    • MXA902 6.0.32
    • MXW 10.0.X
    • P300 6.0.38
    • ULXD4D/4Q 2.8.7
    • SCM820 1.4.3
    • Shure Update Utility 2.8.4
    • Shure Web Device Discovery 1.2.17
फर्मवेयर
6.0.41

Improvements

  • Enhancements to support Designer 6.0.0
  • Additional hardware support

Known Issues

  • AES67 support is only available on UltimoX hardware
    • ANI4IN devices manufactured as of January 2018 are compatible with AES67
  • In AES67 mode - Audio does not pass after changing Dante Device name, followed by a reboot
  • When exporting Presets using Safari on a Mac OS, the file type is saved incorrectly and must be renamed to .json to be imported

Notes

  • User Guide
  • Command Strings
  • To operate this version of ANI4IN with Dante Controller, reference the following minimum versions:
    • v3.10.2.4 (Windows)
    • v3.10.2.3 (Mac OS X)
  • Updating all devices used together to the same firmware version is recommended.
  • To operate this version of ANI4IN with other Shure networked systems, reference the following list of recommended versions supported:
    • ANI22/ANI4IN/ANI4OUT 6.0.41
    • ANIUSB 6.0.44
    • MXA310 6.0.23
    • MXA910 6.0.24
    • MXA920 6.0.38
    • MXA901 6.0.39
    • MXA902 6.0.32
    • MXW 10.0.X
    • P300 6.0.38
    • ULXD4D/4Q 2.8.7
    • SCM820 1.4.3
    • Shure Update Utility 2.8.4
    • Shure Web Device Discovery 1.2.17