Software & Firmware Archives

Release notes cover the following models:

• MXC615
• MXC620/620-F
• MXC630/630-F
• MXC640
• MXCIC
• MXCMIU
• MXCSIGN
• DIS-CCU

Important

• This firmware release can be used to update Microflex Complete (MXC), DCS 6000, or DCS 5900 systems using DIS-CCU, CU 5905, CU 6105, or CU 6110 Central Units.
• Systems using CU 6000, CU 6005, CU 6010 and CU 6011 Central Units are not supported in this release.
• Firmware Upgrade Utility (FUU) v1686, which is included in the release, is required to update MXC devices.

New Features

• MXCMIU
  • Support for XLR input in the MXCMUI when configured as single unit. The use of this input is configured in the DIS-CCU CGUI. The following audio input options are available in the ‘Devices setup’ screen:
    • Port A
    • XLR – line
    • XLR – mic
  • The following option is available in the ‘Participant’ screen:
    • Audio level adjustment: +10 to -20 dB
  • Note: The Port A loudspeaker output and controls are still active when the MXCMUI is configured with XLR audio in.

Improvements

• MXC640
  • Percent indication in voting result screen is now visible when SW6000 is connected
• DIS-CCU (6000 Mode)
  • The state of enabling/disabling of NFC cards is restored after disconnection of SW6000
  • Diagnostics: Cable length info has been removed from the diagnostic report
  • Diagnostics: Cable break info in the diagnostic event log has been updated to report only one of the units connected to the defective cable

Bug Fixes

• DIS-CCU
  • Diagnostics: Incorrect seat number was reported in the Event log at Cable break
  • Diagnostics: Event log did not work when SW6000 was connected
  • Diagnostics: Fixed an error in cable length in the diagnostic report
  • CCU was wrongly storing users’ speaking rights after closing the CUI
• MXC630
  • Secret voting - LEDs turned off after casting first vote
  • Attendance button was not blinking after inserting NFC card during attendance session
  • Voting buttons were not blinking after inserting an NFC card during a voting session
• MXC640
  • "Total" text was not translated for 5-button voting
• MXCMIU
  • Left button functionality Exclusive was not working
• MXCIC
  • The Request icon was cut in the right side
  • Microphone LED was turning off after receiving a “channel occupied” message
  • Two interpreter devices can have same booth and desk number

Known Issues

• Some units in systems with greater than 150 units may not be shown in the Network Topology report.
• Some units may reset when cable breaks in a loop on an EX 6010 unit.
• MXC640
  • Manually entered voting results are not shown if a normal voting session has not been started first
  • The agenda subject name for a manually entered result may be wrong
  • It is not possible to use an MXC640 configured as dual-delegate unit with SW6000 if the use of NFC cards is enabled

Notes

• MXC and DCS 6000 firmware files are packaged together in the same release file.
• To operate MXC devices with version 8.5.1 with other Shure networked systems, see the following list of minimum software and firmware versions:
  • SW6000 6.9.11

New Features

• Support for new bands
• IR Preset Support for P10R+ parameters

Bug Fixes

• Resolved a bug that caused the BAL ST and BAL MX IR presets to not be applied.
• Resolved a bug that caused a mix to be replaced rather than added when setting up CueMode
• Enforcement of Access Control via Wireless Workbench to devices with remote connection has been fixed

Notes

• User Guide
• To operate PSM1000 devices version 1.7.6 with other Shure networked systems, see the following list of supported minimum versions:
  • AXT600 2.1.22
  • Axient Digital 1.2.34
  • ULX-D 2.4.9
  • Wireless Workbench 6.13.1
  • Shure Update Utility 2.4.6
  • ShurePlus Channels 1.4.2

New Features

• Support for new bands
• IR Preset Support for P10R+ parameters

Improvements

• Improved squelch performance
• Improved P10R+ scanning algorithm provides more accurate scan data
• Volume lock was updated to remain persistent after a power cycle. Added a user control to set volume lock on and off
• Removed pan control from the home screen when operating in stereo mode
• Volume Limiter is now set to OFF when restored to its factory default settings

Bug Fixes

• Resolved a bug that caused the BAL ST and BAL MX IR presets to not be applied.
• Resolved a bug that caused a mix to be replaced rather than added when setting up CueMode
• Updated the behavior of some live audio parameter changes so they are all applied immediately, with the exception of volume lock
• Updated POWER SAVE MODE so it clears internal state after a channel or group scan is performed, which resolves a bug that could cause IR sync mismatches
• Updated Channel Scan and Group Scan so it clears after cancellation, which resolves a bug that could cause the home screen to not update according to its current operating frequency

Notes

• User Guide
• To operate PSM1000 devices version 1.7.6 with other Shure networked systems, see the following list of supported minimum versions:
  • AXT600 2.1.22
  • Axient Digital 1.2.34
  • ULX-D 2.4.9
  • Wireless Workbench 6.13.1
  • Shure Update Utility 2.4.6
  • ShurePlus Channels 1.4.2

Improvements

• Bug fixes

Notes

• User Guide
• To operate SBC840M version 1.2.34 with other Shure devices and software, see the following list of minimum versions:
  • Shure Update Utility 2.4.6
  • Wireless Workbench 6.13.1

Improvements

• Bug fixes

Notes

• User Guide
• To operate SBC840 version 1.2.34 with other Shure devices and software, see the following list of minimum versions:
  • Shure Update Utility 2.4.6
  • Wireless Workbench 6.13.1

Improvements

• Bug fixes

Notes

• User Guides: SBC220 | SBC240
• To operate SBC220 or SBC240 version 1.2.34 with other Shure devices and software, see the following list of minimum versions:
  • Shure Update Utility 2.4.6
  • Wireless Workbench 6.13.1

Improvements

• Updated the firmware version number for the purpose of keeping all Axient Digital firmware version numbers aligned for brand-new system installations

Notes

• User Guide
• To operate AD610 version 1.2.34 devices with other Shure systems and software, see the following list of minimum versions:
  • Axient Digital AD1/2 and ADX1/1M/2 Transmitters 1.2.34
  • Axient Digital AD4D/Q Receivers 1.2.34
  • Axient AXT400 Receiver 2.1.11
  • Axient AXT100/200 2.1.11
  • SBRC Shure Battery Rack Charger 1.1.5
  • Shure Update Utility 2.4.6
  • ShurePlus Channels 1.4.2
  • Wireless Workbench 6.13.1

Improvements

• Support for RF band Z16 (Japan): 1240 MHz – 1260 MHz
• Support for G56 (Indonesia, limited to 10mW)

Notes

• User Guide
• Command Strings
• AD4Q version 1.2.34 is compatible with AD4Q devices on version 1.2.34 and below, but it is recommended to update all devices used together to the same firmware version.
• To operate AD4Q version 1.2.34 devices with other Shure systems and software, see the following list of minimum versions:
  • Axient Digital AD1/2 and ADX1/1M/2 Transmitters 1.2.34
  • Axient Digital AD4D/Q Receivers 1.2.34
  • Axient AXT600 Spectrum Manager 2.1.22
  • SBRC Shure Battery Rack Charger 1.1.5
  • Shure Update Utility 2.4.6
  • ShurePlus Channels 1.4.2
  • Wireless Workbench 6.13.1

Improvements

• Support for RF band Z16 (Japan): 1240 MHz – 1260 MHz
• Support for G56 (Indonesia, limited to 10mW)

Bug Fix

• Fixed talk switch support for the AES53 output

Notes

• User Guide
• Command Strings
• AD4D version 1.2.34 is compatible with AD4D devices on version 1.2.34 and below, but it is recommended to update all devices used together to the same firmware version.
• To operate AD4D version 1.2.34 devices with other Shure systems and software, see the following list of minimum versions:
  • Axient Digital AD1/2 and ADX1/1M/2 Transmitters 1.2.34
  • Axient Digital AD4D/Q Receivers 1.2.34
  • Axient AXT600 Spectrum Manager 2.1.22
  • SBRC Shure Battery Rack Charger 1.1.5
  • Shure Update Utility 2.4.6
  • ShurePlus Channels 1.4.2

Improvements

• Support for RF band Z16 (Japan): 1240 MHz – 1260 MHz
• Support for G56 (Indonesia, limited to 10mW)

Notes

• User Guides: AD1 | AD2 | ADX1 | ADX1M | ADX2 | ADX2FD
• AD1/2 and ADX1/1M/2 version 1.2.34 is compatible with devices on version 1.2.34 and below, but it is recommended to update all devices used together to the same firmware version.
• To operate AD1/2 and ADX1/1M/2 version 1.2.34 devices with other Shure systems and software, see the following list of minimum versions:
  • Axient Digital AD1/2 and ADX1/1M/2 Transmitters 1.2.34
  • Axient Digital AD4D/Q Receivers 1.2.34
  • Axient AXT600 Spectrum Manager 2.1.22
  • SBC240/840/840M Chargers 1.2.34
  • SBRC Shure Battery Rack Charger 1.1.5
  • Shure Update Utility 2.4.6
  • ShurePlus Channels 1.4.2
  • Wireless Workbench 6.13.1