Firmware

Firmware updates are an important part of the maintenance of your electronic devices.

Why update the Firmware on Shure Products?
  • Ensure the functionality and interoperability of your Shure hardware and software
  • May include new features and added functionality
  • Delivers minor fixes or patches
What You Need
  • A computer with an Internet connection
  • The Shure Update Utility software (available here)
  • Shure hardware to be updated
  • Cables to connect Shure gear to the computer
  • Network switch for connecting multiple devices at once (Ethernet devices only)

Downloading New Firmware

After downloading firmware to the SUU, devices can be updated offline if your system is in a location without easy internet access. To download the latest firmware versions, open the Shure Update Utility.

  1. Click the Updates button at the top of the window to open the Download Manager. Note: This button will be labeled either "Check for updates..." or "[#] updates available"
  2. From the Download Manager, select the desired firmware versions. Tip: The dropdown in the upper right allows you to quickly select all or select none.
  3. Click Download, and then Close the Download Manager. Downloaded firmware is listed and can be viewed and managed in the Firmware tab.

Connecting Hardware

Connect your device or network switch to your computer. A wired connection is required when updating device firmware.

A network switch can connect multiple devices simultaneously. A "star" configuration is not required, but is strongly recommended.

Connect the Ethernet or USB port on a single device directly to your computer.

Connection Types

RJ45 Ethernet
RJ45 Ethernet
Cat5e
Cat5e
Micro USB
Micro USB
USB-to-micro-USB
USB-to-micro-USB

To verify your devices are connected properly:

  • Open the Update Devices tab on the Shure Update Utility
  • Confirm all connected devices appear in the list

If any devices do not display:

  • Check all physical connections
  • Ensure all devices are powered on
  • Refer to the Troubleshooting section of the SUU user guide

Send Updates

Push to Connected Devices

Once you've downloaded the firmware, close the Download Manager to return to the main window. In the Update Devices tab, all items to be updated are preselected.

To change the firmware version being sent, double-click the device's row in the Version to install column. When all devices to be updated are checked and the proper version is selected, click Send Updates...

Caution: Do not turn off, unplug or disconnect the system during a firmware update. If an interruption occurs, reconnect the device to your computer and send the relevant updates again.

Firmware update computer screenshot.
Push to Wireless Components

Firmware updates may include firmware for associated wireless components. Certain systems support updating of transmitters when docked in networked charging stations. Others can be connected to your computer directly via USB. These systems can be connected to your computer and updated through the SUU.

Wireless components that are not updated through the SUU use infrared ports to send the updates from the host device to the wireless components. Select your system for detailed instructions on how to initiate an IR update:

  • MXW Transmitter Firmware Updates

    Dock all MXW transmitters in the networked charging station that is connected to the same network and subnet as your computer. Install updates through the SUU as you would any other connected device.

    Note: If the MXW Audio Network Interface is connected via Port 4, ensure that the Network mode is set to Switched mode (default) from the Preferences tab of the ANI control software.

  • QLX-D Transmitter Firmware Updates

    Download the appropriate firmware package to the receiver:

    • HH BP = handheld or bodypack firmware
    • BN GN = gooseneck or boundary firmware
    1. On the receiver, Press menu while holding the enter button to access the advanced menu. Use the menu button to navigate to the update menu.
    2. Press enter to start the update.
    3. When the red IR LED flashes, align the receiver and transmitter IR sync ports. The red LED will remain illuminated to indicate correct alignment and the download will automatically start.
    4. Maintain alignment during the update and monitor download progress (0 to 100%) on the receiver screen.
    5. When the update is complete, "TX Update good" is shown on the receiver display. If the screen shows Err.009, update again with a transmitter type that matches the firmware held by the receiver.

    CAUTION! Do not turn off the transmitter until the update is complete.

  • ULX-D Transmitter Firmware Updates
    1. Go to DEVICE UTILITIES chevron_right TX FW UPDATE on the receiver.
    2. Download the appropriate firmware package to the receiver:
      • HH BP = handheld or bodypack firmware
      • BN GN = gooseneck or boundary firmware
    3. Place the transmitter on its side and align the IR ports.
    4. Press ENTER on the receiver to begin the download to the transmitter. IR ports must be aligned for the entire download, which can take 50 seconds or longer.

    CAUTION! Do not turn off the transmitter until the update is complete.

  • GLX-D Transmitter Firmware Updates

    Connect the devices to your computer using a USB-to-Micro-USB cable. Update firmware through the SUU as you would any other connected device.

    Illustrations of connecting devices to a computer using a USB-to-Micro-USB cable.
  • Axient Digital Transmitter Firmware Updates

    Download firmware to the receiver first, and then update transmitters to the same firmware version to ensure consistent operation.

    1. Go to Device Configuration chevron_right Tx Firmware Update on the receiver.
    2. Place the transmitter on its side and align the IR ports.
    3. Press ENTER on the receiver to begin the download to the transmitter. IR ports must be aligned for the entire download, which can take 50 seconds or longer.

    CAUTION! Do not turn off the transmitter until the update is complete.

  • Axient Transmitter Firmware Updates
    1. Download the transmitter firmware to the AXT400 receiver via the SUU
    2. On the transmitter, navigate to Tx chevron_right IR Presets chevron_right FW Update
    3. Align the receiver and transmitter IR ports and press Download

    Once the download is complete, which can take 50 seconds or longer, the transmitter automatically begins the firmware update, which overwrites the existing firmware.

    CAUTION! Do not turn off the transmitter until the update is complete.

  • PSM1000 Receiver Firmware Updates
    1. On the transmitter, navigate to the Util chevron_right More chevron_right FW Update menu.
    2. Align the receiver and transmitter IR ports and press Download. The download begins, which can take 50 seconds or longer.

    Once the download is complete, the receiver automatically begins the firmware update, which overwrites the existing firmware.

    CAUTION! Do not turn off the transmitter until the update is complete.

  • SLX-D Transmitter Firmware Updates
    1. On the receiver, push the control knob once.
    2. Turn the control knob to scroll to “Advanced Settings” and push it again.
    3. Turn the control knob to get to “Transmitter Firmware” and push.
    4. Turn on the transmitter.
    5. Align the transmitter and receiver IR ports and push the knob to start the update.
    6. Hold the transmitter in place until update confirmation is received.

Troubleshooting

The following are some of the most common issues SUU users have reported. If your issue is not addressed here, please contact Applications Engineering.

ULX-D FIRMWARE UPDATE AND ISSUES

If you have a ULX-D system running version 1.5.6 or older and need to update to the latest, please follow this guide. ULX-D Update Troubleshooting


CONNECTED DEVICES DON'T DISPLAY

Verify that all components are powered on, check all the physical connections and cables, and verify that you are running the latest version of Shure Update Utility. Also be sure to select the correct Network Adaptor in Preferences. For additional troubleshooting steps, including correcting firewall issues, please see Shure Update Utility: Devices Don’t Display in our FAQ database.

Tip: If you receive a Windows Defender Firewall Pop-Up on first run, check the boxes to allow access for all networks (Domain Networks, Private Networks, and Public Networks).


SUU IS LOCKED IN "DISCOVERING..."

When devices in the Update Devices tab constantly show "Discovering...", make sure your computer and your Shure hardware are configured for the same subnet. An easy way to fix this is to set all devices, including the computer, to Automatic or DHCP mode and then restart the Shure equipment to ensure it gets an IP address. A DHCP server on the network is not required, but it is fine if one is present. Model-specific instructions for accessing the network menu and configuring IP addresses are available in the Documentation Finder.

For additional troubleshooting steps, please see Shure Update Utility: Devices Appear as Discovering in our FAQ database.


CURRENT FIRMWARE VERSION DISPLAYS WITH AN ASTERISK AND RED DOT

An asterisk next to the current firmware version indicates a problem with the firmware installed on the device. First, try re-installing the current version. This may take several attempts. After the current version installs correctly, you may update to the new version as normal.

If all devices appear with a red dot, please review Shure Update Utility: All Devices Have Red Dot in our FAQ database.


OLDER FIRMWARE VERSIONS

If you need an older firmware version that is no longer available from within the SUU, you can visit our Firmware Archive

Note: To install firmware downloaded from outside the SUU, you must first download the desired .pack files and import them into SUU from the Firmware tab. You will then be able to install the desired firmware version as described above.

Visit Firmware Archive