Find an Answer

Browse our vast Answer database for answers to many common technical questions.

Sort by:

Most Popular Most Recent

Results per page:

10 25 50 100

Can I use more than one PSM receiver with just one transmitter?

Yes, you can use as many PSM receivers as you want to pick up the signal that a PSM transmitter is broadcasting. All the receivers will need to operate on the same frequency as the transmitter. All the receivers will pick up the ...


Point to point wireless using a Shure PSM system

Point to Point Wireless Audio Systems   Introduction Often it is desirable (or even mandatory) to send an audio signal from one fixed location to another fixed location without wires. This is termed "point-t...


Antenna tip color for bodypacks

Tip Color Frequency Range UR Frequency Band Axient Digital Frequency Band Model Yellow 470 - 530 MHz G...


PSM 900 vs PSM 1000 - primary differences

Here are the primary differences: PSM1000 - tuning range is 72 MHz (36 MHz - PSM900) PSM1000 - dual transmitter (P10T) in one chassis PSM1000 - receiver (P10R) has antenna diversity (non-diversity - PSM900) ...


WWB6 ports and protocol information

AXT400, AXT600, AXT610, AXT630/631, AXT900, P10T, ULXD4, ULXD4D, ULXD4Q, AD4D, AD4Q, AD610, SBRC, SBC220, SBC240, SBC840, SBC840M - Main processor Port TCP/UDP Protocol Description ...


Point to point (PTP) mode on P10T

In the AUDIO menu, choose MODE, then select PTP. This mode allows the P10T to transmit to a UR4 receiver in the same frequency range.


Why does the P10T have two antenna outputs and not a summed output?

The P10T is actually two individual transmitters contained within a single housing. So all the RF components are discreet and independent of one another. Providing a single mixed output, without adding any loss, would require the...


Extra Battery Terminals ULXD1, P9RA, P10R, UR5

The extra contacts only support functionality of the optional SB900A Li-ion rechargeable battery pack. The battery microcontroller communications terminal (on the left) provides the "time remaining" information tha...


P10R current draw

Make certain the P10R is in "Standard Gain" mode. The "High Gain" mode increases the current draw. Driving the headphone amp harder will increase the current draw. Make certain you are feeding the tr...


Carrier for two AA Cells / Batteries

This accessory secures two AA cells (batteries) into the battery compartment of the ULXD1, PR9RA, P10R, and UR5.  Some brands of AA cells have slightly smaller dimensions than others. This plastic carrier properly positions ...


P10T transmitter with P9RA receiver; P9T transmitter with P10R receiver

It is possible to "mix and match" the PSM900 and PSM1000 personal monitor system components.  A P9RA beltpack receiver can be used with a P9T transmitter or a P10T transmitter.  Similarly, a P10R bel...


P10T - No RF combiner inside?

A passive 2:1 combiner inside the P10T would reduce the RF output power by 3dB.  An active combiner would have raised the price substantially and added excessive heat inside the chassis.


WWB6 Unable to Recognize PSM1000 Transmitter

After checking that the network configuration is correct, it is possible that a mismatch in the firmware version of the P10T transmitter and the required firmware version for interoperability with WWB6 software is preventing comm...


P10R Firmware - March 2013

On the P10R (receiver), the original firmware version was 1.1.0, as was the original firmware version of the P10T (transmitter). The 1.1.0 version of the P10T did not communicate with Wireless Workbench 6.  A subse...


PSM1000 ethernet type

10/100.


P10R battery adapter marked as REMOVE

When using two AA cells, this piece helps to keep the two cells secure.   When using a Shure SB900A rechargeable power pack, this piece is removed as the pack is slightly larger that two AA cells. The part number f...


PSM 1000 Firmware 1.3.1 Compatibility

Firmware version 1.3.1 is available and required for P10Ts to work with Axient hardware. Most P10T's are on firmware version 1.1.0, and this version is not compatible with P10T's running version 1.3.1 All ...


Are PSM600 components compatible with PSM900 and PSM1000 components?

The short answer is: not recommended. While it is true that these systems share the same stereo pilot tone and there are certain frequency band combinations that overlap, the companding scheme is quite different and will yield au...


Are PSM700 components compatible with PSM900 and PSM1000 components?

The combination of PSM700 components with PSM900 or PSM1000 components can work reasonably well from an audio and RF standpoint because these systems use the same stereo pilot tone and a similar enough companding scheme. The comp...


P10R Label with the letter "F"

The "F" on the label refers to the an updated battery frame design.


Will a P9R or P10T work with a P7T transmitter?

Sorry, the answer is "No."  The individual frequencies in the PSM700 H3 band do not match the frequencies in the PSM900 G7 band or in the PSM1000 G10 band.don't line up.


Band-limit my wireless mic to be compliant with the 2020 regulations?

You can permanently band-limit your devices to operate in permitted bands per the new FCC regulations using the U.S. 600 MHz Conversion Tool (built into Wireless Workbench) if you own any of the following, operating in the following...


Ask a Question

Contact Service & Repair

Telephone: (800) 516-2525

Fax: (847) 600-8686

Contact Product Support

Telephone: (312) 736-6006