• Page 5 of 43
  1. 1
  2. 2
  3. 3
  4. 4
  5. 5
  6. 6
  7. 7
  8. 8
  9. 9
  10. 10
  11. 43
Filter by: Date Posted Filter by: Title Filter by: Version Associated Products Filter by: File Size
June 20, 2018 MXA910 - Microflex Advance Ceiling Array Microphone 3.0.24 See release notes Download PACK (18.7 mb)

Recommendation

Update all MXA910 devices in a configuration to the same firmware version.

Improvements

  • DSP Updates
    • Faster Auto Position performance: Only 2-3 seconds required for auto position setup
    • Echo Reduction Meter and Faders: Enhanced echo reference level control
    • EQ Contour: New presets for faster room tuning
    • Send to Mix: Assign selected channels to direct out only or direct out and Automix
    • Pre- and Post-Automix Fader
    • Pre- and Post-Automix Mute
    • Automix Gain Meters
  • Hardware Light Bar
    • More color options (now 17 total)
    • More brightness levels (now 6 total, including off)
  • New command strings
  • Bug fixes
    • Devices lock up due to TPCI connection issues
    • Users access GUI without completing password recovery

Known Issues

  • When exporting Presets using Safari on a Mac OS, the file type is saved incorrectly and must be renamed to .json to be imported.

Notes

  • User Guide
  • Command strings
  • MXA910 version 3.0.24 is compatible with MXA910 devices running version 3.0.24 and below, but updating all devices used together to the same firmware version is recommended.
  • To operate MXA910 version 3.0.24 with Dante™ Controller, reference the following minimum versions: v3.10.2.4 (Windows) and v3.10.2.3 (Mac OS X)
  • To operate MXA910 version 3.0.24 with other Shure networked systems, reference the following list of minimum versions supported:
    • ANI22 2.0.18
    • ANI4IN 2.0.18
    • ANI4OUT 2.0.18
    • ANIUSB-MATRIX 2.0.19
    • Designer 3.0
    • MXA310 3.0.24
    • Microflex Wireless 5.2.2
    • P300 IntelliMix® Audio Conferencing Processor 2.1.6
    • ULXD4D/4Q 2.2.24
    • SCM820 1.3.3
    • Shure Update Utility 2.4.2
    • Shure Web Device Discovery 1.2
June 20, 2018 MXA310 - Microflex Advance Table Array Microphone (Dante Only) 3.0.24 See release notes Download PACK (4.41 mb)

Recommendation

Update all MXA310 devices in a configuration to the same firmware version.

Improvements

  • DSP
    • Per-Channel PEQ: Adds PEQ to all channels in MXA310
    • Send to Mix: Assign selected channels to direct out only or direct out and Automix
    • Pre- and Post-Automix Fader
    • Pre- and Post-Automix Mute
    • Automix Gain Meters
  • Hardware Light Ring
    • More color options (now 17 total)
    • More brightness levels (now 6 total, including off)
  • New command strings
  • Bug fixes
    • Devices lock up due to TPCI connection issues
    • Users access GUI without completing password recovery

Known Issues

  • After updating from version 2.X to 3.0.24, Channel EQ settings return to their default settings.
  • When exporting Presets using Safari on a Mac OS, the file type is saved incorrectly and must be renamed to .json to be imported

Notes

  • User Guide
  • Command strings
  • MXA310 version 3.0.24 is compatible with MXA310 devices running version 3.0.24 and below, but updating all devices used together to the same firmware version is recommended.
  • To operate MXA310 version 3.0.24 with Dante Controller, reference the following minimum versions: v3.10.2.4 (Windows) and v3.10.2.3 (Mac OS X)
  • To operate MXA310 version 3.0.24 with other Shure networked systems, reference the following list of minimum versions supported:
    • ANI22 2.0.18
    • ANI4IN 2.0.18
    • ANI4OUT 2.0.18
    • ANIUSB-MATRIX 2.0.19
    • MXA910 3.0.24
    • Microflex Wireless 5.2.2
    • P300 IntelliMix® Audio Conferencing Processor 2.1.6
    • ULXD4D/4Q 2.2.24
    • SCM820 1.3.3
    • Shure Update Utility 2.4.2
    • Shure Web Device Discovery 1.2
June 20, 2018 MXA310 - Microflex Advance Table Array Microphone 3.0.24 See release notes Download PACK (4.67 mb)

Recommendation

Update all MXA310 devices in a configuration to the same firmware version.

Improvements

  • DSP
    • Per-Channel PEQ: Adds PEQ to all channels in MXA310
    • Send to Mix: Assign selected channels to direct out only or direct out and Automix
    • Pre- and Post-Automix Fader
    • Pre- and Post-Automix Mute
    • Automix Gain Meters
  • Hardware Light Ring
    • More color options (now 17 total)
    • More brightness levels (now 6 total, including off)
  • New command strings
  • Bug fixes
    • Devices lock up due to TPCI connection issues
    • Users access GUI without completing password recovery

Known Issues

  • After updating from version 2.X to 3.0.24, Channel EQ settings return to their default settings.
  • When exporting Presets using Safari on a Mac OS, the file type is saved incorrectly and must be renamed to .json to be imported

Notes

  • User Guide
  • Command strings
  • MXA310 version 3.0.24 is compatible with MXA310 devices running version 3.0.24 and below, but updating all devices used together to the same firmware version is recommended.
  • To operate MXA310 version 3.0.24 with Dante Controller, reference the following minimum versions: v3.10.2.4 (Windows) and v3.10.2.3 (Mac OS X)
  • To operate MXA310 version 3.0.24 with other Shure networked systems, reference the following list of minimum versions supported:
    • ANI22 2.0.18
    • ANI4IN 2.0.18
    • ANI4OUT 2.0.18
    • ANIUSB-MATRIX 2.0.19
    • MXA910 3.0.24
    • Microflex Wireless 5.2.2
    • P300 IntelliMix® Audio Conferencing Processor 2.1.6
    • ULXD4D/4Q 2.2.24
    • SCM820 1.3.3
    • Shure Update Utility 2.4.2
    • Shure Web Device Discovery 1.2
June 18, 2018 AD1, AD2, ADX1, ADX1M, and ADX2 - Axient Digital Transmitters 1.0.29 See release notes Download PACK (1.05 mb)

Improvement

  • Resolves intermittent issue in which frequency on transmitter could reset to default value (Group 1, Channel 1) when batteries are fully drained.

Notes

  • AD1/2 version 1.0.29 is compatible with AD1/2 devices on version 1.0.29 and below, but it is recommended to update all devices used together to the same firmware version.
  • To operate AD1/2 version 1.0.29 devices with other Shure systems and software, see the following list of minimum versions:
    • Axient Digital AD4D/Q Receivers 1.0.27
    • Shure Update Utility 2.4.2
    • ShurePlus Channels 1.4
    • Wireless Workbench 6.12.2
June 14, 2018 Microflex Complete, DDS 5900, and DCS 6000 8.3.1 See release notes Download ZIP (175 mb)

Important

  • This firmware release can be used to upgrade units in a DDS 5900 or a DCS 6000 systems using CU 5905, CU 6105, CU 6110 or DIS CCU Central Units.
  • CU 6000, CU 6005, CU 6010 and CU 6011 Central Units are not supported in this release.
  • DIS FUU Firmware Upgrade Utility is required to upgrade devices.

New Feature

  • DCS 6000 (DIS CCU) and CU61XX: Support for Microflex Complete MXC615, MXC620, MXC620-F, MXC630, and MXC630-F

Improvements

  • Bug fixes for DC 6990 P
  • Delegate devices incorrectly handles Mic On in Manual + Reply Mode
  • Speech time is not reset after microphone is turned off
  • Devices may not display delegate name on Welcome screen
  • Exclusive requests behave incorrectly between two devices set as Chairman

Notes

June 14, 2018 ULXD1/2 - Extended Bands Wireless Transmitter 2.2.24 See release notes Download PACK (302 kb)

Important

  • ULX-D 2.X firmware versions are incompatible with ULX-D or QLX-D 1.X firmware versions. To ensure all receivers and transmitters in a configuration function with each other, update all devices to the same firmware version.
  • Transmitters upgraded to version 2.2.24 should not be downgraded to versions 1.5.6 or earlier.

Improvements

  • Support for new frequency bands:
    • U.S. 572 – 616 MHz (J50A)
    • U.S. 653 – 663 MHz (L50A)
  • Bug fixes, including fixing the issue of ULXD1/2 transmitters on version 2.2.23 getting reset to factory default settings after an update or downgrade.

Known Issue

  • ULX-D devices on J50A or L50A frequency bands are not compatible with SystemOn 2.0-3.0.1

Notes

  • User Guide
  • If your ULXD1/2 transmitter is on version 2.2.23, updating to version 2.2.24 will unexpectedly reset your ULXD1 to its factory default settings and your previous settings will need to be recovered via IR sync.
  • Transmitters upgraded to version 2.2.24 should not be downgraded to versions 1.5.6 or earlier.
  • ULXD1/2 transmitters used with receivers must be updated via IR sync. After a receiver is updated, follow these steps:
    1. Go to the receiver menu: DEVICE UTILITIES > TX FW UPDATE
    2. Align the infrared ports with the transmitter
    3. Press ENTER
  • Maintain an IR connection when updating transmitter firmware via IR sync. In rare occasions, upgrades from 1.5.6 or earlier to 1.6.6 or later can cause transmitters to become non-responsive temporarily. If the update fails and the unit is non-responsive, resolve the issue by following these steps:
    1. Using the Shure Update Utility, downgrade the firmware for the ULXD4/ULXD4D/ULXD4Q Receiver to 1.5.6 AND keep the desired transmitter firmware (1.6.6 or later).
    2. Update the transmitter firmware to 1.6.6 or later via IR menu. From the receiver menu: DEVICE UTILITIES > TX FW UPDATE. Align the infrared ports with the transmitter and then press ENTER.
    3. Upgrade receiver to 1.6.6 or later.
  • SystemOn 3.0.1 displays "Check system requirements, your current firmware version may not be confirmed compatible" for ULX-D version 2.2.24; however only ULX-D devices on J50A or L50A frequency bands are not compatible with SystemOn 3.0.1.
  • To operate ULX-D version 2.2.24 devices with other Shure networked systems and software, see the following list of minimum versions:
    • ULX-D ULXD4/4D/4Q Receivers 2.2.24
    • QLX-D QLXD1/2 Transmitters and QLXD4 Receivers 2.2.11
    • Axient AXT600 Spectrum Manager 2.1.11
    • Wireless Workbench  6.12.4
    • Shure Update Utility 2.4.2
    • ShurePlus Channels 1.4.1
    • SystemOn 3.0.1
June 14, 2018 ULXD1/2 - 900 MHz ISM Wireless Transmitter 2.2.24 See release notes Download PACK (518 kb)

Important

  • ULX-D 2.X firmware versions are incompatible with ULX-D or QLX-D 1.X firmware versions. To ensure all receivers and transmitters in a configuration function with each other, update all devices to the same firmware version.
  • Transmitters upgraded to version 2.2.24 should not be downgraded to versions 1.5.6 or earlier.

Improvements

  • Support for new frequency bands:
    • U.S. 572 – 616 MHz (J50A)
    • U.S. 653 – 663 MHz (L50A)
  • Bug fixes, including fixing the issue of ULXD1/2 transmitters on version 2.2.23 getting reset to factory default settings after an update or downgrade.

Known Issue

  • ULX-D devices on J50A or L50A frequency bands are not compatible with SystemOn 2.0-3.0.1

Notes

  • User Guide
  • If your ULXD1/2 transmitter is on version 2.2.23, updating to version 2.2.24 will unexpectedly reset your ULXD1 to its factory default settings and your previous settings will need to be recovered via IR sync.
  • Transmitters upgraded to version 2.2.24 should not be downgraded to versions 1.5.6 or earlier.
  • ULXD1/2 transmitters used with receivers must be updated via IR sync. After a receiver is updated, follow these steps:
    1. Go to the receiver menu: DEVICE UTILITIES > TX FW UPDATE
    2. Align the infrared ports with the transmitter
    3. Press ENTER
  • Maintain an IR connection when updating transmitter firmware via IR sync. In rare occasions, upgrades from 1.5.6 or earlier to 1.6.6 or later can cause transmitters to become non-responsive temporarily. If the update fails and the unit is non-responsive, resolve the issue by following these steps:
    1. Using the Shure Update Utility, downgrade the firmware for the ULXD4/ULXD4D/ULXD4Q Receiver to 1.5.6 AND keep the desired transmitter firmware (1.6.6 or later).
    2. Update the transmitter firmware to 1.6.6 or later via IR menu. From the receiver menu: DEVICE UTILITIES > TX FW UPDATE. Align the infrared ports with the transmitter and then press ENTER.
    3. Upgrade receiver to 1.6.6 or later.
  • SystemOn 3.0.1 displays "Check system requirements, your current firmware version may not be confirmed compatible" for ULX-D version 2.2.24; however only ULX-D devices on J50A or L50A frequency bands are not compatible with SystemOn 3.0.1.
  • To operate ULX-D version 2.2.24 devices with other Shure networked systems and software, see the following list of minimum versions:
    • ULX-D ULXD4/4D/4Q Receivers 2.2.24
    • QLX-D QLXD1/2 Transmitters and QLXD4 Receivers 2.2.11
    • Axient AXT600 Spectrum Manager 2.1.11
    • Wireless Workbench  6.12.4
    • Shure Update Utility 2.4.2
    • ShurePlus Channels 1.4.1
    • SystemOn 3.0.1
June 14, 2018 ULXD4 - Extended Bands Digital Wireless Receiver 2.2.24 See release notes Download PACK (1.91 mb)

Important

  • ULX-D 2.X firmware versions are incompatible with ULX-D or QLX-D 1.X firmware versions. To ensure all receivers and transmitters in a configuration function with each other, update all devices to the same firmware version.

Improvements

  • Support for new frequency bands:
    • U.S. 572 – 616 MHz (J50A)
    • U.S. 653 – 663 MHz (L50A)
  • Added power supply fail-safe protection
  • Bug fixes

Known Issue

  • ULX-D devices on J50A or L50A frequency bands are not compatible with SystemOn 2.0-3.0.1

Notes

  • User Guide
  • ULXD1/2 transmitters used with receivers must be updated via IR sync. After a receiver is updated, follow these steps:
    1. Go to the receiver menu: DEVICE UTILITIES > TX FW UPDATE
    2. Align the infrared ports with the transmitter
    3. Press ENTER
  • Maintain an IR connection when updating transmitter firmware via IR sync. In rare occasions, upgrades from 1.5.6 or earlier to 1.6.6 or later can cause transmitters to become non-responsive temporarily. If the update fails and the unit is non-responsive, resolve the issue by following these steps:
    1. Using the Shure Update Utility, downgrade the firmware for the ULXD4/ULXD4D/ULXD4Q Receiver to 1.5.6 AND keep the desired transmitter firmware (1.6.6 or later).
    2. Update the transmitter firmware to 1.6.6 or later via IR menu. From the receiver menu: DEVICE UTILITIES > TX FW UPDATE. Align the infrared ports with the transmitter and then press ENTER.
    3. Upgrade receiver to 1.6.6 or later.
  • SystemOn 3.0.1 displays "Check system requirements, your current firmware version may not be confirmed compatible" for ULX-D version 2.2.24; however only ULX-D devices on J50A or L50A frequency bands are not compatible with SystemOn 3.0.1.
  • To operate ULX-D version 2.2.24 devices with other Shure networked systems and software, see the following list of minimum versions:
    • ULX-D ULXD1/2/6/8 Transmitters and ULXD4/4D/4Q Receivers 2.2.24
    • SBC250/450/850 Networked Charging Stations 2.2.24
    • QLX-D QLXD1/2 Transmitters and QLXD4 Receivers 2.2.11
    • PSM1000 1.5.12
    • Axient AXT600 Spectrum Manager 2.1.11
    • Wireless Workbench 6.12.4
    • Shure Update Utility 2.4.2
    • ShurePlus Channels 1.4.1
    • SystemOn 3.0.1
June 14, 2018 ULXD4 - Digital Wireless Receiver 2.2.24 See release notes Download PACK (1.91 mb)

Important

  • ULX-D 2.X firmware versions are incompatible with ULX-D or QLX-D 1.X firmware versions. To ensure all receivers and transmitters in a configuration function with each other, update all devices to the same firmware version.

Improvements

  • Support for new frequency bands:
    • U.S. 572 – 616 MHz (J50A)
    • U.S. 653 – 663 MHz (L50A)
  • Added power supply fail-safe protection
  • Bug fixes

Known Issue

  • ULX-D devices on J50A or L50A frequency bands are not compatible with SystemOn 2.0-3.0.1

Notes

  • User Guide
  • ULXD1/2 transmitters used with receivers must be updated via IR sync. After a receiver is updated, follow these steps:
    1. Go to the receiver menu: DEVICE UTILITIES > TX FW UPDATE
    2. Align the infrared ports with the transmitter
    3. Press ENTER
  • Maintain an IR connection when updating transmitter firmware via IR sync. In rare occasions, upgrades from 1.5.6 or earlier to 1.6.6 or later can cause transmitters to become non-responsive temporarily. If the update fails and the unit is non-responsive, resolve the issue by following these steps:
    1. Using the Shure Update Utility, downgrade the firmware for the ULXD4/ULXD4D/ULXD4Q Receiver to 1.5.6 AND keep the desired transmitter firmware (1.6.6 or later).
    2. Update the transmitter firmware to 1.6.6 or later via IR menu. From the receiver menu: DEVICE UTILITIES > TX FW UPDATE. Align the infrared ports with the transmitter and then press ENTER.
    3. Upgrade receiver to 1.6.6 or later.
  • SystemOn 3.0.1 displays "Check system requirements, your current firmware version may not be confirmed compatible" for ULX-D version 2.2.24; however only ULX-D devices on J50A or L50A frequency bands are not compatible with SystemOn 3.0.1.
  • To operate ULX-D version 2.2.24 devices with other Shure networked systems and software, see the following list of minimum versions:
    • ULX-D ULXD1/2/6/8 Transmitters and ULXD4/4D/4Q Receivers 2.2.24
    • SBC250/450/850 Networked Charging Stations 2.2.24
    • QLX-D QLXD1/2 Transmitters and QLXD4 Receivers 2.2.11
    • PSM1000 1.5.12
    • Axient AXT600 Spectrum Manager 2.1.11
    • Wireless Workbench 6.12.4
    • Shure Update Utility 2.4.2
    • ShurePlus Channels 1.4.1
    • SystemOn 3.0.1
June 14, 2018 ULXD4D - Extended Bands Dual Channel Digital Wireless Receiver 2.2.24 See release notes Download PACK (5.25 mb)

Important

  • ULX-D 2.X firmware versions are incompatible with ULX-D or QLX-D 1.X firmware versions. To ensure all receivers and transmitters in a configuration function with each other, update all devices to the same firmware version.

New Feature

  • AES67 support

Improvements

  • Support for new frequency bands:
    • U.S. 572 – 616 MHz (J50A)
    • U.S. 653 – 663 MHz (L50A)
  • Added power supply fail-safe protection
  • Bug fixes

Known Issue

  • ULX-D devices on J50A or L50A frequency bands are not compatible with SystemOn 2.0-3.0.1

Notes

  • User Guide
  • If your ULXD4D/Q is on version 1.3.6 or older, first upgrade to version 1.4.8 before upgrading to the latest version of ULX-D. Because version 1.4.8 is no longer available on Shure Update Utility, you will need to download the firmware from Shure's Firmware Archive. Follow these steps:
    1. Download Shure Update Utility
    2. Download ULXD4D version 1.4.8 or ULXD4Q version 1.4.8 to your computer and copy the .pack file to Documents > Shure > Firmware
    3. Launch Shure Update Utility, connect your devices to your computer, and follow SUU instructions on uploading new firmware to devices.
  • ULXD1/2 transmitters used with receivers must be updated via IR sync. After a receiver is updated, follow these steps:
    1. Go to the receiver menu: DEVICE UTILITIES > TX FW UPDATE
    2. Align the infrared ports with the transmitter
    3. Press ENTER
  • Maintain an IR connection when updating transmitter firmware via IR sync. In rare occasions, upgrades from 1.5.6 or earlier to 1.6.6 or later can cause transmitters to become non-responsive temporarily. If the update fails and the unit is non-responsive, resolve the issue by following these steps:
    1. Using the Shure Update Utility, downgrade the firmware for the ULXD4/ULXD4D/ULXD4Q Receiver to 1.5.6 AND keep the desired transmitter firmware (1.6.6 or later).
    2. Update the transmitter firmware to 1.6.6 or later via IR menu. From the receiver menu: DEVICE UTILITIES > TX FW UPDATE. Align the infrared ports with the transmitter and then press ENTER.
    3. Upgrade receiver to 1.6.6 or later.
  • SystemOn 3.0.1 displays "Check system requirements, your current firmware version may not be confirmed compatible" for ULX-D version 2.2.24; however only ULX-D devices on J50A or L50A frequency bands are not compatible with SystemOn 3.0.1.
  • To operate ULX-D version 2.2.24 devices with other Shure networked systems and software, see the following list of minimum versions:
    • ULX-D ULXD1/2/6/8 Transmitters and ULXD4/4D/4Q Receivers 2.2.24
    • SBC250/450/850 Networked Charging Stations 2.2.24
    • QLX-D QLXD1/2 Transmitters and QLXD4 Receivers 2.2.11
    • PSM1000 1.5.12
    • Axient AXT600 Spectrum Manager 2.1.11
    • Wireless Workbench 6.12.4
    • Shure Update Utility 2.4.2
    • ShurePlus Channels 1.4.1
    • SystemOn 3.0.1