ULXS4Standard Diversity Receiver
Shure
The Shure ULX® Standard receiver offers an exceptional value in both performance and price, for both working musicians and sound installers.
The feature set of the versatile ULXS4 receiver offers a direct path to full, clear audio signals, unencumbered and unattached.
For use with ULX Standard Wireless systems.
ULXS4 Wireless Diversity Receiver
- Automatic Frequency Selection with group scan function
- Up to 1440 selectable frequencies
- 5-segment transmitted audio signal strength meter
- RF indicator
- 3-segment transmitter battery fuel gauge
- Advanced multi-function LCD displays group and channel
- Mic/Line switch
- Detachable 1/4-wave antenna
- XLR and 1/4-inch output
- Rugged plastic chassis
- 1/2 rack design
- RF Carrier Frequency Range
- 470.000 to 865.000 MHz (Available frequencies depend on the applicable regulations in the country where the system is used). Refer to the frequency supplement supplied with the system.
- Effective Range
- 100 m (300 ft.) under optimal conditions
- NOTE: Actual working range depends on RF signal absorption, reflection, and interference
- Audio Frequency Response
- 25 to 15,000 Hz, +/- 2 dB
- NOTE: Overall system frequency response depends on the microphone element.
- Transmitter Audio Polarity
- Positive pressure on microphone diaphragm (or positive voltage applied to tip of WA302 phone plug) produces positive voltage on pin 2 (with respect to pin 3 of low impedance output) and the tip of the high impedance 1/4-inch output
- Transmitter Gain Adjustment Range
- ULX1: 25 dB
- ULX2: 25 dB
- Receiver Audio Output Level (+/- 38 kHz deviation, 1 kHz tone)
- XLR connector (into 600 ohm load): +3.9 dBV (line), -17 dBV (mic)
- 1/4 inch connector (into 3000 ohm load): -2 dBV
- Impedance
- ULX1 (input): 1 Megohm ULXS4, ULXP4 (output): 50 ohms at line level; 2000 ohms at mic level
- Modulation
- +/- 38 kHz deviation compressor-expander system with pre- and de-emphasis.
- RF Power Output
- ULX1, ULX2: 30 mW maximum
- Dynamic Range
- >100 dB, A-weighted
- RF Sensitivity
- 1.26 microVolt for 12 dB SINAD (typical)
- Image Rejection
- 80 dB typical
- Spurious Rejection
- 75 dB typical
- Ultimate Quieting (reference +/- 38 kHz deviation)
- >105 dB, A-weighted
- System Distortion (reference +/- 38 kHz deviation, 1 kHz modulation)
- 0.3% total harmonic distortion, typical
- Power Requirements
- ULX1, ULX2: 9V alkaline battery; 8.4 V Nicad optional
- ULXS4, ULXP4: 14 - 18 Vdc (negative ground), 550 mA
- Battery Life
- 8 to 9 hours (with 9V alkaline battery)
- Operating Temperature Range
- -20 degrees to 49 degrees C (-4 degrees to 120 degrees F)
- NOTE: Battery characteristics may limit this range.
- Overall Dimensions
- ULX1: 96.5 mm H x 67 mm W x 26.7 mm D (3.86 x 2.68 x 1.10 in.)
- ULX2/SM58: 228.6 L x 51 mm Dia. (9 x 2 in)
- ULX2/BETA 58: 220.9 mm L x 51 mm Dia. (8.7 x 2 in.)
- ULX2/SM86: 213 mm L x 49 mm Dia. (8.4 in x 1.9 in)
- ULX2/87, ULX2/BETA 87: 223.5 mm L x 51 mm Dia. (8.8 x 2 in.)
- ULX4S: 43 mm H x 214 mm W x 163 mm D (1.72 in. x 8.56 in. x 6.52 in.)
- ULX4P: 43 mm H x 214 mm W x 172 mm D (1.72 in. x 8.56 in. x 6.88 in.)
- Net Weight
- ULX1: 79 g (2.8 oz.) without battery
- ULX2/58, ULX2/BETA 58: 289 g (10.2 oz.) without battery
- ULX2/SM86: 251 g (8.8 oz.) without battery
- ULX2/87, ULX2/BETA 87: 258 g (9.1 oz.) without battery
- ULXS4: 1049 g (2 lbs, 5 oz.)
- ULXP4: 1105 g (2 lbs, 7 oz.)
- ULXP4, ULXS4 Receiver Audio Output
Connector Unbalanced (1/4 in.) Balanced (XLR) Actual Impedance 3 kilohm Mic. Level: 1848 Ohms
Line Level: 75 OhmsPin Assignments Tip = Hot
Ring/Sleeve = Ground1 = Ground
2 = Hot
3 = ColdPhantom Power Protection? Yes Yes - ULXP4, ULXS4 Receiver Antenna Input
Connector Type BNC Actual Impedance 50 Ohms Nominal Input Level -95 to -30 dBm Maximum Input Level +6 dBm (-20 dBm recommended) Pin Assignments Shell = Ground, Center = Signal Voltage for Remote Power 12 Vdc, 150 mA maximum
| Name | Availability | |
|---|---|---|
|
UA507 Dual Rack Mount HardwareRack hardware for Dual ULX Receivers, P4M, P4T, DFR11EQ5, DP11EQ, SCM262 or SCM268 |
Where To Buy |
|
UA506 Single Rack Mount KitRack hardware for single ULX receiver, P4M, P4T, DFR11EQ5, DP11EQ, SCM262 or SCM268 |
Where To Buy |
| User Guides | Language | File Size |
|---|---|---|
| ULX Wireless User Guide (English) | English | 1360 (kb) |
| ULX Wireless User Guide (French) | French | 1375 (kb) |
| ULX Wireless User Guide (German) | German | 1356 (kb) |
| ULX Wireless User Guide (Italian) | Italian | 1673 (kb) |
| ULX Wireless User Guide (Japanese) | Japanese | 5097 (kb) |
| ULX Wireless User Guide (Korean) | Korean | 2189 (kb) |
| ULX Wireless User Guide (Portuguese) | Portuguese | 1352 (kb) |
| ULX Wireless User Guide (Spanish) | Spanish | 1333 (kb) |
